Biomechanical Behavior of Dynamic vs. Static Distal Locking Intramedullary Nails in Subtrochanteric Femur Fractures.

OBJECTIVE: Hip fractures are one of the most frequent fractures presenting to the emergency department and orthopedic trauma teams. The aim of this study was to determine the best indication and therapeutic technique for subtrochanteric fractures and unifying criteria when choosing the most suitable type of nail. MATERIALS AND METHODS: To analyze the influence of the material and the type of distal locking of intramedullary nails (static or dynamic), a femur model with a fracture in the subtrochanteric region stabilized with a long Gamma intramedullary nail was applied using finite element method (FEM) simulation. RESULTS: The mechanical study shows that titanium nails allow for greater micromobility at the fracture site, which could act as a stimulus for the formation of callus and consolidation of the fracture. In the mechanical study, the type of distal locking mainly affects mobility at the fracture site and stress in the cortical bone around the distal screws, without in any case exceeding values that may compromise the viability of the assembly or that may result in detrimental effects (in terms of mobility at the fracture site) for the consolidation process. CONCLUSION: Subtrochanteric fractures treated with titanium nail and static distal locking is safe and does not hinder consolidation.

Close2U: An App for Monitoring Cancer Patients with Enriched Information from Interaction Patterns.

The management of cancer patients' symptoms in doctor consultations is a cornerstone in clinical care, this process being fundamental for the follow-up of the evolution of these. This article presents an application that allows collecting periodically and systematically the data of cancer patients and their visualization by the medical team. In this article, we made the analysis, design, implementation, and final evaluation by analyzing the correlation of this data collection with interaction patterns to determine how the user information can be enriched with information from the interaction patterns. We have followed an agile methodology based on the iterative and incremental development of successive prototypes with increased fidelity, where the requirements and solutions have evolved over time according to the need and assessments made. The comprehensive analysis of the patient's condition allowed us to perform a first analysis of the correlation of the states of patients concerning mood, sleeping quality, and pain with the interaction patterns. A future goal of this project is to optimize the process of data collection and the analysis of information. Another future goal is to reduce the time dedicated to reporting the evolution of symptoms in face-to-face consultations and to help professionals in analyzing the patient's evolution even in the period that has not been attended in person.

A New Multiparameter Model for Multiaxial Fatigue Life Prediction of Rubber Materials.

Most of the mechanical components manufactured in rubber materials experience fluctuating loads, which cause material fatigue, significantly reducing their life. Different models have been used to approach this problem. However, most of them just provide life prediction only valid for each of the specific studied material and type of specimen used for the experimental testing. This work focuses on the development of a new generalized model of multiaxial fatigue for rubber materials, introducing a multiparameter variable to improve fatigue life prediction by considering simultaneously relevant information concerning stresses, strains, and strain energies. The model is verified through its correlation with several published fatigue tests for different rubber materials. The proposed model has been compared with more than 20 different parameters used in the specialized literature, calculating the value of the R2 coefficient by comparing the predicted values of every model, with the experimental ones. The obtained results show a significant improvement in the fatigue life prediction. The proposed model does not aim to be a universal and definitive approach for elastomer fatigue, but it provides a reliable general tool that can be used for processing data obtained from experimental tests carried out under different conditions.

The use of Barthel index for the assessment of the functional recovery after osteoporotic hip fracture: One year follow-up.

The Barthel index evolution was analyzed in a sample of older people with osteoporotic hip fracture in order to verify the influence of comorbidities and cognitive impairment on the physical recovery of those patients, during the first year following the fracture. A prospective observational study was carried out between October 1, 2012 and March 31, 2013. A sample of 247 individuals was initially selected. After a primary revision, 39 participants were excluded (clearly not meeting inclusion criteria, lack of data, or not agree to participate in the study), and finally a total of 208 participants were included in the analysis, 166 women, with an average age of 84.59 years, and 42 men, with an average age of 82.05. 54.80% of all cases were older than 85 years. The mean Barthel index value prior to fracture was 76.63, decreasing to 64.91 at one-year follow-up. Only 22.12% of patients achieved a full recovery for activities of daily living. A statistical analysis was performed by comparing Barthel index recovery depending on the values of Charlson and Pfeiffer indexes, respectively. The mean differences in Barthel index drop between the one-year follow-up and the hospital admission values were found statistical significant (p<0.01). These findings indicate that Charlson and Pfeiffer indexes clearly influence the Barthel index recovery. Low values of Charlson and Pfeiffer indexes resulted in better Barthel index recovery. In conclusion, the Barthel index is a good tool to evaluate the physical recovery after osteoporotic hip fracture.

Visco-Hyperelastic Model with Damage for Simulating Cyclic Thermoplastic Elastomers Behavior Applied to an Industrial Component.

In this work a nonlinear phenomenological visco-hyperelastic model including damage consideration is developed to simulate the behavior of Santoprene 101-73 material. This type of elastomeric material is widely used in the automotive and aeronautic sectors, as it has multiple advantages. However, there are still challenges in properly analyzing the mechanical phenomena that these materials exhibit. To simulate this kind of material a lot of theories have been exposed, but none of them have been endorsed unanimously. In this paper, a new model is presented based on the literature, and on experimental data. The test samples were extracted from an air intake duct component of an automotive engine. Inelastic phenomena such as hyperelasticity, viscoelasticity and damage are considered singularly in this model, thus modifying and improving some relevant models found in the literature. Optimization algorithms were used to find out the model parameter values that lead to the best fit of the experimental curves from the tests. An adequate fitting was obtained for the experimental results of a cyclic uniaxial loading of Santoprene 101-73.

Finite element simulation and clinical follow-up of lumbar spine biomechanics with dynamic fixations.

Arthrodesis is a recommended treatment in advanced stages of degenerative disc disease. Despite dynamic fixations were designed to prevent abnormal motions with better physiological load transmission, improving lumbar pain and reducing stress on adjacent segments, contradictory results have been obtained. This study was designed to compare differences in the biomechanical behaviour between the healthy lumbar spine and the spine with DYNESYS and DIAM fixation, respectively, at L4-L5 level. Behaviour under flexion, extension, lateral bending and axial rotation are compared using healthy lumbar spine as reference. Three 3D finite element models of lumbar spine (healthy, DYNESYS and DIAM implemented, respectively) were developed, together a clinical follow-up of 58 patients operated on for degenerative disc disease. DYNESYS produced higher variations of motion with a maximum value for lateral bending, decreasing intradiscal pressure and facet joint forces at instrumented level, whereas screw insertion zones concentrated stress. DIAM increased movement during flexion, decreased it in another three movements, and produced stress concentration at the apophyses at instrumented level. Dynamic systems, used as single systems without vertebral fusion, could be a good alternative to degenerative disc disease for grade II and grade III of Pfirrmann.

Influence of gap size, screw configuration, and nail materials in the stability of anterograde reamed intramedullary nail in femoral transverse fractures.

Femoral shaft fractures are among the most severe injuries of the skeleton. They are associated with high morbidity and mortality. The most appropriate treatment depending on the type of fracture and location level should be chosen. A finite element model of the femur has been developed, analyzing various types of fractures in the subtrochanteric and diaphyseal supracondylar area, with several gap sizes, being stabilized with a single combination of screws for the intramedullary nail. The mechanical strength of the nail against bending and compression efforts was studied comparing two materials for the nail: stainless steel and titanium alloy. Beside the finite elements (FE) simulations, a clinical follow-up was carried out, considering a sample of 55 patients, 24 males, and 31 females, with mean age of 52.5 years. Localizations of fractures were 22 in the right femur and 33 in the left one, respectively. A good agreement between clinical results and the simulated fractures in terms of gap size was found. Non-comminuted fractures have a mean consolidation time of 4.1 months, which coincides with the appropriate mobility at fracture site obtained in the FE simulations, whereas comminuted fractures have a higher mean consolidation period estimated in 7.1 months, corresponding to the excessive mobility at fracture site obtained by means of FE simulations. The obtained results between both nail materials (stainless steel and titanium alloy) show a higher mobility when using titanium nails, which produce a higher rate of strains at the fracture site, amplitude of micromotions and bigger global movements compared to stainless-steel nails. Steel nails provide stiffer osteosyntheses than the titanium nails. In conclusion, anterograde locked nail is particularly useful in the treatment of a wide range of supracondylar fractures with proximal extension into the femoral diaphysis.

Influence of screw combination and nail materials in the stability of anterograde reamed intramedullary nail in distal femoral fractures.

Intramedullary nailing (IM) is a technique universally accepted to treat femoral diaphyseal fractures. The treatment of fractures located in the distal third remains a controversial issue though. A finite element model of the femur has been developed, analyzing distal fractures with several gap sizes combined with different interlocking combinations of distal screws with one oblique screw proximally to stabilize the intramedullary nail. The mechanical strength of the nail against bending and compression efforts was also studied. Beside the FE simulations, a clinical follow-up of 15 patients, 6 males and 9 females, with mean age of 53.2 years was carried out. Localizations of fractures were 10 in the right femur and 5 in the left femur, respectively. A fairly good correspondence agreement between clinical results and the simulated fractures in terms of gap size was found. Non-comminuted fractures had a mean consolidation time of 20.5 weeks (4.8 months), a tendency corresponding well to the mobility obtained in the FE simulations; Comminuted fractures on the other hand exhibited a higher mean consolidation period of 22.2 weeks (5.2 months) secondary to the excessive mobility at fracture site obtained by means of FE simulations. The best stability at fracture site was found for the system with three distal screws and the system with two distal screws placed medial lateral. The highest leverage of distal screws was obtained maximizing the distance between them and choosing the coronal plane for their orientation. The results obtained with both nail materials (stainless steel and titanium alloy) show a higher mobility when using titanium nails. Steel nails provide stiffer osteosyntheses than the titanium nails. In conclusion, the best screw combination in terms of stability to produce fracture healing and the least difficulties during treatment is the one which had one oblique proximal screw with two distal lateral screw implanted in the coronal plane.

Comparative Analysis of the Biomechanical Behaviour of Two Cementless Short Stems for Hip Replacement: Linea Anatomic and Minihip.

A comparative study between two stems (Linea Anatomic and Minihip) has been performed in order to analyse the differences in their biomechanical behaviour, concerning stem micromotions and load transmission between stem and bone. From the corresponding finite element models, a parametric study was carried out to quantify ranges of micromotions taking into account: friction coefficient in the stem-bone interface, press-fit and two types of gait cycle. Micromotions were evaluated for each stem at six different levels along repeated gait cycles. An initial and marked stem subsidence at the beginning of the simulation was observed, followed by an asymptotic decrease due to friction forces. Once migration occurs, a repeated reversible cyclic micromotion is developed and stabilized as gait cycle times are simulated. The general motion pattern exhibited higher amplitude of micromotion for Minihip compared to Linea stem. The load transmission mechanism was analyzed, identifying the main internal forces. The results show higher local forces for Minihip stem up to 80% greater than for Linea stem. The differences of design between Minihip and Linea conditioned different distributions of load, influencing the posterior stress-shielding. Consequently, short stems require high bone stock and quality should, being indicated for young patients with high bone quality.

Application of a model based on dual-energy X-ray absorptiometry and finite element simulation for predicting the probability of osteoporotic hip fractures to a sample of people over 60 years.

The aim of this work is the application of a mechanical predictive model to a sample of people over 60 years of age, in order to analyze the fracture probability related to age and sex. A total of 223 elderly people (63 men, aged 63-88, 72.32±6.10; 157 women, aged 61-89, 73.28±5.73) participated in the study. A dual-energy X-ray absorptiometry scanner was used to measure the bone mineral content and bone mineral density at total hip and femoral neck. The application of the predictive model also required a finite element simulation of the proximal femur, obtaining the mechanical damage and fracture probability maps corresponding to each sex and age groups analyzed. Statistical analysis shows higher values of bone mineral density, and consequently of Young's modulus, for men than for women. In general, a decrease of BMD is observed since 65 years old. The maximum mechanical damage value is always located at the femoral neck. The results indicate that mechanical damage tends to increase with age. Coherently with mechanical damage, the maximum fracture probability value is always located at the femoral neck and tends to increase with age. The simulation model to determine the probability of fracture is more complete than the simple measurement of bone mineral density, because provides additional information about mechanical properties of bone, and allows for a prospective detection of fracture risk. The model may be used for risk evaluation in specific patients, if anatomical and dual-energy X-ray absorptiometry measurements are available, helping us to decide about preventive pharmacological treatment for hip fracture.

Cementless hydroxyapatite coated hip prostheses.

More than twenty years ago, hydroxyapatite (HA), calcium phosphate ceramics, was introduced as a coating for cementless hip prostheses. The choice of this ceramic is due to its composition being similar to organic apatite bone crystals. This ceramic is biocompatible, bioactive, and osteoconductive. These qualities facilitate the primary stability and osseointegration of implants. Our surgical experience includes the implantation of more than 4,000 cementless hydroxyapatite coated hip prostheses since 1990. The models implanted are coated with HA in the acetabulum and in the metaphyseal area of the stem. The results corresponding to survival and stability of implants were very satisfactory in the long-term. From our experience, HA-coated hip implants are a reliable alternative which can achieve long term survival, provided that certain requirements are met: good design selection, sound choice of bearing surfaces based on patient life expectancy, meticulous surgical technique, and indications based on adequate bone quality.

Prevalence of osteoporotic vertebral fracture in Spanish women over age 45.

The aim of this work is to study the prevalence of osteoporotic vertebral fractures in Spanish women over 45 years of age, based on the selection of a nationwide sample. An observational, cross-sectional, multicenter study was conducted during 2006, in all of Spain's regions. The sample analyzed was of 5000 individuals, representative of the female population over age 45 in Spain. A questionnaire was used to determine which factors are most often associated with vertebral fractures. We also assessed whether the Prevalent Vertebral Fracture Index, proposed by Vogt, is useful in indicating a possible osteoporotic vertebral fracture. Five hundred orthopedic surgeons, from various Spanish regions, were trained in different aspects of the study: inclusion and exclusion criteria, management of the risk factor questionnaire, and implementation of the Vogt questionnaire. The number of fracture cases was 1549 (31.79%). 528 Women (34.08%) had a single vertebral fracture, and 1021 (65.92%) had multiple vertebral fractures. The following factors were statistically significantly associated with vertebral fracture: age, late menarche, early menopause, diabetes mellitus, hyperparathyroidism, rheumatoid arthritis, height loss, daily physical activity, corticosteroid therapy, personal history of osteoporotic fracture and previous diagnosis of osteoporosis. The differences in Vogt score according to age and fracture status were statistically significant. The conclusion of the study is that vertebral osteoporotic fracture in the female Spanish population is frequent. The high prevalence in the Spanish population older than 60 years is probably related to malnutrition in the period from 1936 to 1952.

Study of the polycarbonate-urethane/metal contact in different positions during gait cycle.

Nowadays, a growing number of young and more active patients receive hip replacement. More strenuous activities in such patients involve higher friction and wear rates, with friction on the bearing surface being crucial to ensure arthroplasty survival in the long term. Over the last years, the polycarbonate-urethane has offered a feasible alternative to conventional bearings. A finite element model of a healthy hip joint was developed and adjusted to three gait phases (heel strike, mid-stance, and toe-off), serving as a benchmark for the assessment of the results of joint replacement model. Three equivalent models were made with the polycarbonate-urethane Tribofit system implanted, one for each of the three gait phases, after reproducing a virtual surgery over the respective healthy models. Standard body-weight loads were considered: 230% body-weight toe-off, 275% body-weight mid-stance, and 350% body-weight heel strike. Contact pressures were obtained for the different models. When comparing the results corresponding to the healthy model to polycarbonate-urethane joint, contact areas are similar and so contact pressures are within a narrower value range. In conclusion, polycarbonate-urethane characteristics are similar to those of the joint cartilage. So, it is a favorable alternative to traditional bearing surfaces in total hip arthroplasty, especially in young patients.

Mid-term study of bone remodeling after femoral cemented stem implantation: comparison between DXA and finite element simulation.

This five-year prospective study was designed to investigate periprosthetic bone remodeling associated with two cemented stem models, ABG-II (Stryker) and VerSys (Zimmer), randomly implanted in patients older than 75 years. The sample consisted of 64 cases (32, ABG-II; 32, VerSys). Inclusion criterion was diagnosis of osteoarthritis recommended for cemented total hip arthroplasty. Besides clinical study, Finite Element (FE) simulation was used to analyze biomechanical changes caused by hip arthroplasty. Bone Mineral Density (BMD) measurements showed a progressive increase in bone mass throughout the entire follow-up period for both stems, well correlated with FE results except in Gruen zones 4, 5, 6 for ABG-II and in zones 4, 5 for VerSys, denoting that remodeling in those zones does not depend on mechanical factors but rather on biological or physiological ones.

Study of the behavior of a bell-shaped colonic self-expandable NiTi stent under peristaltic movements.

Managing bowel obstruction produced by colon cancer requires an emergency intervention to patients usually in poor conditions, and it requires creating an intestinal stoma in most cases. Regardless of that the tumor may be resectable, a two-stage surgery is mandatory. To avoid these disadvantages, endoscopic placement of self-expanding stents has been introduced more than 10 years ago, as an alternative to relieve colonic obstruction. It can be used as a bridge to elective single-stage surgery avoiding a stoma or as a definitive palliative solution in patients with irresectable tumor or poor estimated survival. Stents must be capable of exerting an adequate radial pressure on the stenosed wall, keeping in mind that stent must not move or be crushed, guaranteeing an adequate lumen when affected by peristaltic waves. A finite element simulation of bell-shaped nitinol stent functionality has been done. Catheter introduction, releasing at position, and the effect of peristaltic wave were simulated. To check the reliability of the simulation, a clinical experimentation with porcine specimens was carried out. The stent presented a good deployment and flexibility. Stent behavior was excellent, expanding from the very narrow lumen corresponding to the maximum peristaltic pressure to the complete recovery of operative lumen when the pressure disappears.

Development and kinematic verification of a finite element model for the lumbar spine: application to disc degeneration.

The knowledge of the lumbar spine biomechanics is essential for clinical applications. Due to the difficulties to experiment on living people and the irregular results published, simulation based on finite elements (FE) has been developed, making it possible to adequately reproduce the biomechanics of the lumbar spine. A 3D FE model of the complete lumbar spine (vertebrae, discs, and ligaments) has been developed. To verify the model, radiological images (X-rays) were taken over a group of 25 healthy, male individuals with average age of 27.4 and average weight of 78.6 kg with the corresponding informed consent. A maximum angle of 34.40° is achieved in flexion and of 35.58° in extension with a flexion-extension angle of 69.98°. The radiological measurements were 33.94 ± 4.91°, 38.73 ± 4.29°, and 72.67°, respectively. In lateral bending, the maximum angles were 19.33° and 23.40 ± 2.39, respectively. In rotation a maximum angle of 9.96° was obtained. The model incorporates a precise geometrical characterization of several elements (vertebrae, discs, and ligaments), respecting anatomical features and being capable of reproducing a wide range of physiological movements. Application to disc degeneration (L5-S1) allows predicting the affection in the mobility of the different lumbar segments, by means of parametric studies for different ranges of degeneration.

Long-term outcomes of a new model of anatomical hydroxyapatite-coated hip prosthesis.

This prospective study was designed to evaluate 196 Anatomique Benoist Giraud (ABG II) total hip arthroplasties which were implanted between September 1999 and December 2000. A minimum 11 years follow up was completed in 183 cases. The bearing surfaces were polyethylene-zirconia in 84 cases, polyethylene-metal in 42 and ceramic-ceramic in 57. Changes in the femoral stem design, in relation to the previous ABG I model, have led to a significant improvement in stress-shielding. Polyethylene wear rate was lower by more than 50% compared with non-crosslinked polyethylene. Excellent and good results were obtained in 90.32% of cases, and implant survival was 98.39% at the end of follow-up.

A mechanical model for predicting the probability of osteoporotic hip fractures based in DXA measurements and finite element simulation.

BACKGROUND: Osteoporotic hip fractures represent major cause of disability, loss of quality of life and even mortality among the elderly population. Decisions on drug therapy are based on the assessment of risk factors for fracture, from BMD measurements. The combination of biomechanical models with clinical studies could better estimate bone strength and supporting the specialists in their decision. METHODS: A model to assess the probability of fracture, based on the Damage and Fracture Mechanics has been developed, evaluating the mechanical magnitudes involved in the fracture process from clinical BMD measurements. The model is intended for simulating the degenerative process in the skeleton, with the consequent lost of bone mass and hence the decrease of its mechanical resistance which enables the fracture due to different traumatisms. Clinical studies were chosen, both in non-treatment conditions and receiving drug therapy, and fitted to specific patients according their actual BMD measures. The predictive model is applied in a FE simulation of the proximal femur. The fracture zone would be determined according loading scenario (sideway fall, impact, accidental loads, etc.), using the mechanical properties of bone obtained from the evolutionary model corresponding to the considered time. RESULTS: BMD evolution in untreated patients and in those under different treatments was analyzed. Evolutionary curves of fracture probability were obtained from the evolution of mechanical damage. The evolutionary curve of the untreated group of patients presented a marked increase of the fracture probability, while the curves of patients under drug treatment showed variable decreased risks, depending on the therapy type. CONCLUSION: The FE model allowed to obtain detailed maps of damage and fracture probability, identifying high-risk local zones at femoral neck and intertrochanteric and subtrochanteric areas, which are the typical locations of osteoporotic hip fractures.The developed model is suitable for being used in individualized cases. The model might better identify at-risk individuals in early stages of osteoporosis and might be helpful for treatment decisions.

Applications of finite element simulation in orthopedic and trauma surgery.

Research in different areas of orthopedic and trauma surgery requires a methodology that allows both a more economic approach and the ability to reproduce different situations in an easy way. Simulation models have been introduced recently in bioengineering and could become an essential tool in the study of any physiological unity, regardless of its complexity. The main problem in modeling with finite elements simulation is to achieve an accurate reproduction of the anatomy and a perfect correlation of the different structures, in any region of the human body. Authors have developed a mixed technique, joining the use of a three-dimensional laser scanner Roland Picza captured together with computed tomography (CT) and 3D CT images, to achieve a perfect reproduction of the anatomy. Finite element (FE) simulation lets us know the biomechanical changes that take place after hip prostheses or osteosynthesis implantation and biological responses of bone to biomechanical changes. The simulation models are able to predict changes in bone stress distribution around the implant, so allowing preventing future pathologies. The development of a FE model of lumbar spine is another interesting application of the simulation. The model allows research on the lumbar spine, not only in physiological conditions but also simulating different load conditions, to assess the impact on biomechanics. Different degrees of disc degeneration can also be simulated to determine the impact on adjacent anatomical elements. Finally, FE models may be useful to test different fixation systems, i.e., pedicular screws, interbody devices or rigid fixations compared with the dynamic ones. We have also developed models of lumbar spine and hip joint to predict the occurrence of osteoporotic fractures, based on densitometric determinations and specific biomechanical models, including approaches from damage and fracture mechanics. FE simulations also allow us to predict the behavior of orthopedic splints applied to the correction of deformities, providing the recovering force-displacement and angle-moment curves that characterize the mechanical behavior of the splint in the overall range of movement.

Male osteoporosis: A review.

Osteoporosis in men is a heterogeneous disease that has received little attention. However, one third of worldwide hip fractures occur in the male population. This problem is more prevalent in people over 70 years of age. The etiology can be idiopathic or secondary to hypogonadism, vitamin D deficiency and inadequate calcium intake, hormonal treatments for prostate cancer, use of toxic and every disease or drug use that alters bone metabolism.Risk factors such as a previous history of fragility fracture should be assessed for the diagnosis. However, risk factors in men are very heterogeneous. There are significant differences in the pharmacological treatment of osteoporosis between men and women fundamentally due to the level of evidence in published trials supporting each treatment. New treatments will offer new therapeutic prospects. The goal of this work is a revision of the present status knowledge about male osteoporosis.